Boom Kites Vector montage du speed system .pdf
Nom original: Boom Kites Vector montage du speed system.pdfTitre: Boom Kites Vector montage du speed systemAuteur: RollandMots-clés: Boom Kites Vector montage du speed system.pdf
Ce document au format PDF 1.4 a été généré par PDFCreator Version 0.9.3 / GPL Ghostscript 8.54, et a été envoyé sur fichier-pdf.fr le 09/09/2010 à 12:42, depuis l'adresse IP 82.252.x.x.
La présente page de téléchargement du fichier a été vue 1845 fois.
Taille du document: 1 Mo (33 pages).
Confidentialité: fichier public
Aperçu du document
speedaddon
Page 1 sur 33
Speedsystem Addon
If you want to add the speed system to your BOOM Vector, please follow these steps.
The whole process takes about 1/2 to 1 hour.
1. Lay out the kite and the parts from the SpeedSys addon. The left line is the brake/safety
line, the right line is the right flying line.
2. The two long lines build the "T" line, that connects the two B line pulleys. They are looped
into each other.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 2 sur 33
3. The short thin line is looped in the "T" line like that:
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 3 sur 33
4. The brake line joint is replaced by the fat short line.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 4 sur 33
6. The "T" - line is in front of the brake line - connect the brake extension line and the "T" line
using a black line joint.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 5 sur 33
7. Now open the right line joint.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 6 sur 33
8. Take all A lines except the outmost and ...
... loop them on the black speed-line above the stopper - like seen below.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 7 sur 33
9. The "T" line, the B - lines and the outmost A line are looped on the short pulley - line.
Do it this way: first the T line, then the B lines, finally the A lines.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 8 sur 33
10. Now loop the line over the pulley ...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 9 sur 33
... until it looks like that.
11. Take the C lines and the wingtip line ...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 10 sur 33
... and loop them on the straight piece of black line. It should now look like that:
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 11 sur 33
12. Put the pulley in the speed system (The T line is behind the A lines) ...
... and connect the two loops using a black line joint.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 12 sur 33
13. Redo all above steps for the left side and your setup will look like that:
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 13 sur 33
14. Now it's time for the "Y" lines - loop one of them into the left system ...
... the other one into the right system and you end up like that:
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 14 sur 33
15. Next step is to add the black part of the Y.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 15 sur 33
We take the pulley ..
... loop it in and you end up like that: (Please note - both ends of the white line below should be
sleeved)
16. Connect the left side ...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 16 sur 33
... pull the figure 8 knot through the pulley ...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 17 sur 33
and attach the right part.
It looks that way now.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 18 sur 33
17. Here comes the bar - setup. We see an old version of the mono harness line and the
ancient safety-system.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 19 sur 33
18. Remove the neoprene on the right side ...
... and remove the leader line, too.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 20 sur 33
19. Pull off the harness line ...
... and put on one side of the new harness line.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 21 sur 33
20. Also put the middle part on the bar ...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 22 sur 33
... and move all that into the middle of the bar.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 23 sur 33
21. Do not forget to adjust the length of the safety leader line and put the leader line and the
neoprene back on the bar. All leader lines have the same lengths.
22. Here we attach the speed adjustment strap:
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 24 sur 33
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 25 sur 33
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 26 sur 33
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 27 sur 33
The same part upside down:
23. Put it through the D ring on the middle part ...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 28 sur 33
... and put it through the tube at the adjustment strap.
24. Knot it there ...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 29 sur 33
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 30 sur 33
this knot works well, although it's not the original bowline knot. (Flo always makes the knot
that way...)
25. OK! Ready!
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 31 sur 33
26. Now wrap all lines around the harness line a few turns...
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 32 sur 33
... and continue with "8"'s to prevent tangles and twists.
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
speedaddon
Page 33 sur 33
Finished. Thanks to Flo for showing all that!
http://web.archive.org/web/20021105021704/www.boom-kites.com/speedsys/speedad... 09/09/2010
Télécharger le fichier (PDF)
Boom Kites Vector montage du speed system.pdf (PDF, 1 Mo)