Fichier PDF

Partage, hébergement, conversion et archivage facile de documents au format PDF

Partager un fichier Mes fichiers Boite à outils PDF Recherche Aide Contact



service manual. PAGE 600 .pdf


Nom original: service_manual. PAGE 600.pdf
Titre: service_manual. PAGE 600

Ce document au format PDF 1.4 a été généré par PDFCreator Version 1.1.0 / GPL Ghostscript 9.0, et a été envoyé sur fichier-pdf.fr le 19/02/2011 à 19:41, depuis l'adresse IP 212.198.x.x. La présente page de téléchargement du fichier a été vue 968 fois.
Taille du document: 142 Ko (1 page).
Confidentialité: fichier public




Télécharger le fichier (PDF)









Aperçu du document


Clutch:
• Tighten the clutch sleeve hub nut to the specified
torque.

5C-19

12

11

13

Tightening torque
Clutch sleeve hub nut: 150 N·m (15.0 kgf-m, 108.5
lb-ft)

“G”

• Lock the clutch sleeve hub nut with a center punch.

15

14/15

14

15
I823H1530049-03

11. No. 3 drive plate
12. No. 1 drive plate
13. No. 2 drive plate
14. No. 2 driven plate (1 – 4 pcs.)
: The No. 1 and No. 2 driven plates are 9 in total.
15. No. 1 driven plate (8 – 5 pcs.)
: The No. 1 and No. 2 driven plates are 9 in total.
“G”: Direction of outside
I823H1530045-01

• Install the spring washer seat (9) and spring washer
(10) onto the clutch sleeve hub correctly.
10

9

NOTE
Three kinds of the drive plate (No. 1, No. 2
and No. 3) are equipped in the clutch system,
they can be distinguished by the inside
diameter and clutch facing “H”.

“H”

I823H1530047-01

• Insert the clutch drive plates and driven plate one by
one into the clutch sleeve hub in the prescribed order.

I823H1530050-02

“H”: Clutch facing
: Make sure to check the numbers of clutch facing, before installing
them.

NOTE
Insert the outermost No. 2 drive plate claws
“E” to the other slits “F” of clutch housing as
shown in the figure.

Drive plate
No. 1
No. 2
No. 3

I.D.
126 mm (4.96 in)
127 mm (5.00 in)
135 mm (5.31 in)

Clutch facing “H”
36 pcs.
60 pcs.
60 pcs.

NOTE

“F”
“E”

I823H1530048-04

Two kinds of the driven plate (No. 1 and No.
2) are equipped in the clutch system, they
can be distinguished by the thickness.
The No. 1 and No. 2 driven plates are 9 pcs. in
total. 5 – 8 pcs. of No. 1 driven plates are
used with 4 – 1 pc(-s). of No. 2 driven plate(-s)
as a set.
The No. 2 driven plate(-s) must be installed to
4th to 7th position of driven plates order from
the sleeve hub side.
Driven plate
No. 1
No. 2

Thickness
2.0 mm (0.08 in)
2.3 mm (0.09 in)


Aperçu du document service_manual. PAGE 600.pdf - page 1/1

Documents similaires


Fichier PDF service manual page 600
Fichier PDF service manual page 604
Fichier PDF mxer50 cap 09 trasmissione
Fichier PDF kxr50 cap 09 trasmissione
Fichier PDF atv250 09 trasmissione
Fichier PDF mxu250 cap09 trasmissione


Sur le même sujet..