KXR50 cap 02 (plastiche marmitta) .pdf



Nom original: KXR50 cap 02 (plastiche marmitta).pdf

Ce document au format PDF 1.3 a été généré par Word / Mac OS X 10.2.8 Quartz PDFContext, et a été envoyé sur fichier-pdf.fr le 18/03/2013 à 14:00, depuis l'adresse IP 92.155.x.x. La présente page de téléchargement du fichier a été vue 538 fois.
Taille du document: 787 Ko (9 pages).
Confidentialité: fichier public


Aperçu du document


2. FRAME COVERS/EXHAUST MUFFLER

Mongoose/KXR 90/50

2
__________________________________________________________________________________

2

__________________________________________________________________________________

__________________________________________________________________________________

__________________________________________________________________________________

__________________________________________________________________________________

FRAME COVERS/EXHAUST MUFFLER
__________________________________________________________________________________

SERVICE INFORMATION -------------------------------------------FRAME COVERS ------------------------------------------------------EXHAUST MUFFLER REMOVAL ----------------------------------TAILLIGHT BULB -----------------------------------------------------

2- 2
2- 3
2- 7
2- 8

2-0

2. FRAME COVERS/EXHAUST MUFFLER

2-1

Mongoose/KXR 90/50

2. FRAME COVERS/EXHAUST MUFFLER

Mongoose/KXR 90/50

SERVICE INFORMATION
GENERAL INSTRUCTIONS
• When removing frame covers, use special care not to pull them by force because the cover joint
claws may be damaged.
• Make sure to route cables and harnesses according to the Cable & Harness Routing.
TORQUE VALUES
Exhaust muffler lock bolt
Exhaust muffler lock nut

3.2_ 3.8kgf-m
1.8_ 2.2kgf-m

TROUBLESHOOTING
Noisy exhaust muffler
• Damaged exhaust muffler
• Exhaust muffler joint air leaks
Lack of power
• Caved exhaust muffler
• Exhaust muffler air leaks
• Clogged exhaust muffler

2-2

2. FRAME COVERS/EXHAUST MUFFLER

Mongoose/KXR 90/50
Bolts

FRAME COVERS
HANDLEBAR COVER REMOVAL
Remove the two screws attaching the
handlebar cover.
Disconnect the oil level indicator leads
(Mongoose/KXR 50).
Remove the handlebar cover.
INSTALLATION
Reverse the “HANDLEBAR COVER
REMOVAL” procedures.

Handlebar Cover
Seat Lock Lever

SEAT REMOVAL
To remove the seat, pull upward the seat
lock lever and pull up the seat at the rear.

To install the seat, align the tabs on the seat
with the grommets on the frame and press
the seat down until it locks.

°ØMake sure that the seat is securely fitted.

Seat
Bolts

HANDLEBAR REMOVAL
Remove handlebar cover. (See page 2-3)
Remove the rear brake master cylinder
attaching bolts (disk brake).
Disconnect the rear brake cable (drum
brake).
Disconnect the handlebar switch coupler
and lead (under front fender).

2-3

Handlebar Switch Coupler and Lead

2. FRAME COVERS/EXHAUST MUFFLER

Front Brake Cables

Disconnect the front brake cables.
Disconnect the remote stop switch and
front brake stop switch leads.

Remote Engine Stop
Switch Leads

Remove the two screws and speed limiter
cover.
Disconnect the throttle cable.

Remove the two bolts and handlebar cover
holder.
Remove the four bolts and upper handlebar
holders.
Remove the handlebar.

Mongoose/KXR 90/50

Screws

Bolts

Front Brake Stop
Switch Leads
Throttle Cable

Bolts

INSTALLATION
Reverse the “HANDLEBAR REMOVAL”
procedures. (See page 12-13)

°ØRefer to the “BRAKE LEVER FREE

PLAY” section in the chapter 3 to adjust
brake lever free play.

2-4

2. FRAME COVERS/EXHAUST MUFFLER
FRONT FENDER REMOVAL
Remove the seat. (See page 2-3)
Remove the handlebar. (See page 2-3)

Mongoose/KXR 90/50

Screws

Screws

Remove the six screws and nuts attaching
the front fender and right/left foot boards.

Remove the four screws and two nuts
attaching the front fender and rear fender at
the right/left side.

Screws

Screws

Bolts

Remove the two bolts attaching front fender
at the right/left side.

Remover the fuel filler cap.

Fuel Filler Cap

°ØAfter remove, be sure to tighten the fuel
filler cap.

Remove the front fender and disconnect the
ignition switch coupler.

°ØDuring removal, do not pull the joint
claws forcedly to avoid damage.

2-5

Ignition Switch Coupler

2. FRAME COVERS/EXHAUST MUFFLER

Mongoose/KXR 90/50

INSTALLATION
Reverse the “FRONT FENDER
REMOVAL” procedures.

°ØAfter remove, be sure to tighten the fuel
filler cap.

REAR FENDER REMOVAL
Remove the front fender. (See page 2-5)
Remove the battery. (See page 14-4)

Starter Relay

Ignition Unit

Remove the starter relay and CDI unit.

Remove the ten screws attaching the rear
fender and foot boards at the right/left side.

Screws

Screws

Bolts

Remove the two screws attaching the rear
fender at the rear.
Remove the three bolts attaching the rear
fender at the center and then remove the rear
fender.

Screws

2-6

2. FRAME COVERS/EXHAUST MUFFLER

Mongoose/KXR 90/50
Bolts

FOOT BOARD REMOVAL
Remove front fender. (See page 2-5)
Remover rear fender. (See page 2-6)
Remove the four bolts attaching the
right/left foot board.

FRONT CARRIER REMOVAL
Remove the four bolts attaching front carrier
at the right/left side.

Bolts

EXHAUST MUFFLER
REMOVAL
Remove the two nuts attaching the exhaust
pipe and cylinder head.

Nuts

Remove the three bolts attaching the exhaust
muffler, then remove the exhaust muffler.

Bolts

2-7

2. FRAME COVERS/EXHAUST MUFFLER

Mongoose/KXR 90/50

Inspect the gasket.
If the exhaust gas leaks, the gasket should be
replaced.
Install by reversing the removal sequence.
Torque:
Exhaust muffler lock bolt: 3.2_ 3.8kgf-m
Exhaust muffler lock nut: 1.8_ 2.2kgf-m

°ØBe sure to install a new exhaust gasket.

Gasket

TAILLIGHT BULB
REMOVAL
Remove the two screws and taillight lens.

Scresw

Turn bulb and remove it.

Bulb

2-8


KXR50 cap 02 (plastiche marmitta).pdf - page 1/9
 
KXR50 cap 02 (plastiche marmitta).pdf - page 2/9
KXR50 cap 02 (plastiche marmitta).pdf - page 3/9
KXR50 cap 02 (plastiche marmitta).pdf - page 4/9
KXR50 cap 02 (plastiche marmitta).pdf - page 5/9
KXR50 cap 02 (plastiche marmitta).pdf - page 6/9
 




Télécharger le fichier (PDF)


KXR50 cap 02 (plastiche marmitta).pdf (PDF, 787 Ko)

Télécharger
Formats alternatifs: ZIP



Documents similaires


kxr50 cap 02 plastiche marmitta
atv250 02 pp e marmitta
mxer50 cap 02 plastiche marmitta
mxu250 cap02 plastiche e marmitta
atv250 19 luci strumentaz clacson
kxr50 cap 17 luci strumentaz clacson

Sur le même sujet..