KXR50 cap 16 (imp avviamento) .pdf



Nom original: KXR50 cap 16 (imp avviamento).pdf

Ce document au format PDF 1.3 a été généré par Word / Mac OS X 10.2.8 Quartz PDFContext, et a été envoyé sur fichier-pdf.fr le 18/03/2013 à 14:03, depuis l'adresse IP 92.155.x.x. La présente page de téléchargement du fichier a été vue 556 fois.
Taille du document: 1.8 Mo (10 pages).
Confidentialité: fichier public


Aperçu du document


16. STARTING SYSTEM

Mongoose/KXR 90/50

16
__________________________________________________________________________________

__________________________________________________________________________________

__________________________________________________________________________________

16

__________________________________________________________________________________

__________________________________________________________________________________

STARTING SYSTEM
__________________________________________________________________________________

SERVICE INFORMATION -------------------------------------------- 16STARTER MOTOR ----------------------------------------------------- 16STARTER RELAY------------------------------------------------------ 16STARTER CLUTCH (Mongoose/KXR 90) --------------------------- 16STARTER PINION (Mongoose/KXR 50) ----------------------------- 16-

2
3
6
7
9

16-0

16. STARTING SYSTEM

Mongoose/KXR 90/50

Starter Motor

STARTING CIRCUIT
Starter Relay

R/W

G

R

Y/R

Fuse

Ignition Switch

Start
Switch

G/Y

Stoplight
G/Y
Battery

Starter
Motor

G
Front

Rear

Stop Switches

16-1

16. STARTING SYSTEM

Mongoose/KXR 90/50

SERVICE INFORMATION
GENERAL INSTRUCTIONS
• The removal of starter motor can be accomplished with the engine installed.

TROUBLESHOOTING
Starter motor won‘t turn
• Fuse burned out
• Weak battery
• Faulty ignition switch
• Faulty starter clutch
• Faulty front or rear stop switch
• Faulty starter relay
• Poorly connected, broken or shorted wire
• Faulty starter motor
• Faulty change gear control unit

Lack of power
• Weak battery
• Loose wire or connection
• Foreign matter stuck in starter motor
or gear
Starter motor rotates but engine does
not start
• Faulty starter clutch
• Starter motor rotates reversely
• Weak battery

16-2

16. STARTING SYSTEM

Mongoose/KXR 90/50

STARTER MOTOR

Starter Motor

REMOVAL

°ØBefore removing the starter motor, turn

the ignition switch OFF and remove the
battery ground. Then, turn on the
ignition switch and push the starter
button to see if the starter motor
operates properly.

Disconnect the starter motor cable.
Remove two mounting bolts at the starter
motor attaching left crankcase, then remove
the starter motor. (Mongoose/KXR 90’s
starter motor is located on the engine.
Mongoose/KXR 50’s starter motor is
located under the engine.)

Bolts
Front Cover

DISASSEMBLY
Remove the two starter motor case screws,
front cover, motor case and other parts.

Motor Case

INSPECTION
Inspect the removed parts for wear, damage
or discoloration and replace if necessary.
Clean the commutator if there is metal
powder between the segments.

Check for continuity between pairs of the
commutator segments and there should be
continuity.
Also, make a continuity check between
individual commutator segments and the
armature shaft. There should be no
continuity.

16-3

Case Screws
Commutator

16. STARTING SYSTEM

Mongoose/KXR 90/50

STARTER MOTOR CASE
CONTINUITY CHECK
Check to confirm that there is no continuity
between the starter motor wire terminal and
the motor front cover.
Also check for the continuity between the
wire terminal and each brush.
Replace if necessary.

Wire Terminal

Measure the length of the brushes.
Service Limit: 8.5mm replace if below

Check for continuity between the brushes.
If there is continuity, replace with new
ones.

Bearing

Check if the needle bearing in the front cover
turns freely and has no excessive play.
Replace if necessary.
Check the dust seal for wear or damage.

Dust Seal

16-4

16. STARTING SYSTEM

Mongoose/KXR 90/50
Front Cover

Commutator

ASSEMBLY
Apply grease to the dust seal in the front
cover.
Install the brushes onto the brush holders.
Apply a thin coat of grease to the two ends
of the armature shaft.
Insert the commutator into the front cover.

°Ø• Be careful not to damage the brush and
armature shaft mating surfaces.
• When installing the commutator, the
armature shaft should not damage the
dust seal lip.

Grease
O-ring

Install a new O-ring to the front cover.
Install the starter motor case, aligning the
tab on the motor case with the groove on the
front cover.
Tighten the starter motor case screws.

°ØWhen assembling the front cover and
motor case, slightly press down the
armature shaft to assemble them.

Motor Case

S TARTER MOTOR INSTALLATION
Connect the starter motor cable connector
Check the O-ring for wear or damage and
replace it if necessary.
Apply grease to the O-ring and install the
starter motor.
Tighten the two mounting bolts.
Torque: 0.8_ 1.2kgf-m

°ØThe starter motor cable connector must
be installed properly.

16-5

O-ring

16. STARTING SYSTEM
STARTER RELAY

Mongoose/KXR 90/50
Starter Relay

INSPECTION
Remove the seat. (Refer to the chapter 2)
Turn the ignition switch ON and the starter
relay is normal if you hear a click when the
starter button is depressed.
If there is no click sound:
• Inspect the starter relay voltage
• Inspect the starter relay ground circuit
• Check for continuity between the starter
relay yellow/red and green/red wire
terminals
S TARTER RELAY VOLTAGE
INS PECTION
Connect a 12V battery across the starter
relay yellow/red and green/red wire
terminals.
Connect an electric tester between the
starter relay large terminals and check for
continuity between the two terminals.
The relay is normal if there is continuity.
Replace the starter relay with a new one if
there is no continuity.

Starter Relay (Mongoose/KXR 90)

Starter Relay (Mongoose/KXR 50)

16-6

16. STARTING SYSTEM

Mongoose/KXR 90/50
Reduction Gear Case

STARTER PINION
(Mongoose/KXR 90)
REMOVAL
Remove the left crankcase cover and drive
pulley face. (Refer to chapter 9)
Remove the starter one-way clutch drive
nut.
Special

Lock nut socket wrench

E015
Starter One-way Clutch Drive Nut

Remove starter one-way clutch drive.
Special

Start clutch puller

E006

Remove the reduction gear case.
Remove the reduction gear.

Starter Gear Shaft

Reduction Gear

INSTALLATION
Install each washer to the top and bottom of
the reduction gear.
Apply grease to the reduction gear shaft
forcing part.
Then, install in the reverse order of removal.

Washers

Reduction Gear Case

Starter Oneway Clutch Drive Gear

STARTER ONE-WAY CLUTCH
DISASSEMBLY
Remove the 32mm lock nut with special
tool.
Take the starter one-way clutch drive gear
off.
Special

Lock nut socket wrench

E015
32mm Lock Nut

16-7

16. STARTING SYSTEM

Mongoose/KXR 90/50

INSPECTION
Inspect the starter one-way clutch drive gear
teeth for burrs/chips/roughness/wear.
Inspect the starter one-way clutch drive gear
contacting surfaces for pitting/wear/damage.

Contacting Surfaces

Teeth

Push the weight roller to arrow direction for
unsmooth operation. _ Replace starter
clutch assembly.

ASSEMBLY
Install the starter one-way clutch driver gear in
the reverse order of removal.



Starter Oneway Clutch

32mm Lock Nut

Do not reuse the starter clutch bolts that
have been removed.

s Torque: 5.0_ 6.0kgf-m

Starter Clutch Bolts

Starter Oneway Clutch
Drive Gear

Check starter clutch operation.
Clutch operation checking steps:
s Install the starter wheel gear to the starter
clutch, and hold the starter clutch.
s When turning the wheel gear clockwise (1)
the starter clutch and the wheel gear should
be engaged. If not, the starter clutch is
faulty. Replace it.
s When turning the wheel gear
counterclockwise (2), the wheel gear
should turn freely. If not, the starter clutch
is faulty. Replace it.

16-8

16. STARTING SYSTEM

Mongoose/KXR 90/50
Starter Pinion

STARTER PINION
(Mongoose/KXR 50
REMOVAL
Remove the left crankcase cover.
Remove the drive pulley.
(Refer to chapter 9)
Remove the starter pinion cover.
Remove the starter pinion.

Starter Pinion Cover

INSPECTION
Inspect the starter pinion seat for wear.
Inspect the starter pinion for smooth
operation.
Inspect the starter pinion shaft forcing parts
for wear and damage.

Shaft Forcing Parts

INSTALLATION
Apply a small amount of grease to the
starter pinion teeth.
Install the starter pinion in the reverse order
of removal.
Starter Pinion

16-9


Aperçu du document KXR50 cap 16 (imp avviamento).pdf - page 1/10
 
KXR50 cap 16 (imp avviamento).pdf - page 2/10
KXR50 cap 16 (imp avviamento).pdf - page 3/10
KXR50 cap 16 (imp avviamento).pdf - page 4/10
KXR50 cap 16 (imp avviamento).pdf - page 5/10
KXR50 cap 16 (imp avviamento).pdf - page 6/10
 




Télécharger le fichier (PDF)


KXR50 cap 16 (imp avviamento).pdf (PDF, 1.8 Mo)

Télécharger
Formats alternatifs: ZIP



Documents similaires


kxr50 cap 16 imp avviamento
atv250 18 imp avviamento
mxu250 cap18 imp avviamento
mxer50 cap 16 imp avviamento
atv250 09 trasmissione
0686 05a

Sur le même sujet..