manuel A5.pdf


Aperçu du fichier PDF manuel-a5.pdf - page 6/48

Page 1...4 5 67848



Aperçu texte


E-GRIP Operating Instructions (continued from page 8)
TM

Remote Coil: Connecting and Disconnecting

E
N
G
L
I
S
H

WARNING
NEVER INSTALL PRESSURIZED AIR TO THE MARKER WITHOUT THE
TOMBSTONE PUSH PIN
INSTALLED AND THE TOMBSTONE LATCH
IS SET - HOLDING THE TOMBSTONE
IN PLACE
.

1) ❏ Remove the air supply from the marker Remote Coil as outlined in
the Air Supply Cylinder Removal instructions on pages 18-20. Never
disassemble a marker or remove a remote coil that is under pressure.
2) ❏ Check that the Tombstone
Push Pin
is installed.
3) ❏ Check that the Tombstone
Latch
is set .
4) ❏ Check that Gas Line Adapter
and nipple fitting
are secure.
5) ❏ Pull and hold the Remote Coil
fitting Locking Ring
down
to install
or remove the Remote Coil fitting .
6) ❏ With the Locking Ring held
down , push the coil fitting
up onto the nipple
and release
the locking ring up to lock .
7) ❏ Pull down
on the
Remote Coil fitting
to be sure it has locked properly.
❏ To turn off air supply: turn flow control
completely out
❏ To turn on air supply: turn flow control
completely in

E-GRIP OPERATING INSTRUCTIONS

WARNING
READ AND FOLLOW THE E-GRIPTM OPERATING INSTRUCTIONS (PAGES 813) COMPLETELY BEFORE INSTALLING THE AIR SUPPLY CYLINDER AS
OUTLINED IN – GETTING STARTED - STEP 2: ON PAGE 6.
• INSTALL THE AIR SUPPLY AND LOAD THE HOPPER WITH PAINTBALLS
ONLY AFTER YOU:
❏ HAVE THE BARREL BLOCKING DEVICE INSTALLED (SEE PAGE 2);
❏ HAVE THE TRIGGER SAFETY IN SAFE MODE (SEE PAGE 4);
❏ HAVE SUCCESSFULLY INSTALLED THE BATTERY ( STEP 1: PAGE 9) AND
❏ ARE FAMILIAR WITH THE E-GRIP NORMAL OPERATION (STEP 2: PAGE 9).
• EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN
BY THE USER AND ANY PERSON WITHIN RANGE.

• READ EACH STEP COMPLETELY BEFORE PERFORMING THE STEP:

8

E-GRIP Operating Instructions
(continued on page 9)
TM

STEP 1: E-GRIP Battery Installation or Replacement:
To Install the battery: ❏ Remove the battery door
from
the back of the E-GripTM by pulling up and back on the tab .
from the battery,
NOTE: When removing the battery clip
Do Not pull it off by the wires .
❏ Plug a 9 volt battery into the battery clip.
❏ Insert the battery into the E-GripTM with the battery clip
at the top and wires
as shown.
❏ Reinstall the battery door - Replace the battery door with
down, press the tab
and listen for the snap as
the tab
it locks back into the E-GripTM.
NOTE: The E-GripTM Low Battery Indicator feature: the “Ready
To Fire” Flashing Green LED will turn to blinking red when
the battery is low and needs replaced (see - Low Battery
Condition on page 10).
STEP 2: Power On - Basic Operation
1) To turn the E-GripTM power on:
❏ Use a small object like an allen wrench (
) to
press and hold the power button
for 2 seconds.
will light orange then green when the
The LED
electronics have been activated.
❏ Release the power button and the green LED
will
begin flashing green to show the power is on and the
battery is good. (NOTE: ❏ If the LED begins flashing
red, see - Low Battery Condition on page 10).
❏ If pressing the power button failed to turn on
the LED light, see Troubleshooting section on page 13.
2) Safety/Selector operation has three settings:
The 3-position safety/selector switch
S = Safe (as shown);
F = Semi-Auto
(One pull/release
of the trigger
fires 1 time).
FA = Special Firing Mode. The Special Firing Mode can be set to any 1
of 5 firing options as detailed in the Special Firing Mode section.
3) To fire the marker - ❏ select either the F or FA position using the safety/
selector switch and pull the trigger. The LED
will light orange with each
pull of the trigger.
4) Changing Special Firing Modes - ❏ To change the Special Firing Mode
while the E-GripTM is powered on, press and hold the power button
for a
1/2 second. The LED will flash orange to represent the number of the Special
TM

9

E-GRIP Operating Instructions
(continued on page 10)
TM

E
N
G
L
I
S
H