Fichier PDF

Partage, hébergement, conversion et archivage facile de documents au format PDF

Partager un fichier Mes fichiers Boite à outils PDF Recherche Aide Contact



2011 fit engine block heater .pdf



Nom original: 2011 fit - engine block heater.pdf

Ce document au format PDF 1.4 a été généré par FrameMaker 8.0 / Acrobat Distiller 8.2.0 (Windows), et a été envoyé sur fichier-pdf.fr le 18/02/2014 à 01:37, depuis l'adresse IP 192.226.x.x. La présente page de téléchargement du fichier a été vue 356 fois.
Taille du document: 203 Ko (6 pages).
Confidentialité: fichier public




Télécharger le fichier (PDF)









Aperçu du document


Accessory

INSTALLATION
INSTRUCTIONS
PARTS LIST
Engine Block Heater kit
P/N 08T44-SNA-101

Application

Publications No.

AII 45089
ENGINE BLOCK HEATER

2011 FIT

Issue Date

NOV 2010

Engine Block Heater Bracket kit
P/N 08T44-TK6-100
Bracket

Engine block heater

Aluminum washer

Washer-bolt

Heater harness

TOOLS AND SUPPLIES REQUIRED
Ratchet
10 mm, 19 mm, and 24 mm Sockets
Protective cap

100 mm (4 in.) Extension
Torque wrench
Diagonal cutters
Heavy gloves

12 Black wire ties
(6 not used)

Drain pan
Tape measure
White marker
Honda All Season Antifreeze/Coolant Type 2
Fender cover

7

Wire ties with clip
(3 not used)

5

White wire ties
(Not used)

© 2010 American Honda Motor Co., Inc. – All Rights Reserved.

NOTE: Using an extension longer than 100 mm (4 in.) will
give you an incorrect torque reading.

AII 45089 (1011)

08T44-TK6-1000-91

1 of 6

Illustration of the Engine Block Heater Installed on the
Vehicle

4.

Place a clean drain pan under the radiator drain
plug, then remove the drain plug from the bottom of
the radiator to drain the coolant. Remove the radiator
cap to increase the flow.

NOTICE
Radiator coolant will damage paint. Quickly rinse any
spilled coolant from painted surfaces.
RADIATOR CAP

HEATER HARNESS

INSTALLATION
NOTE:
• Always use Honda All Season Antifreeze/Coolant
Type 2. Using a non-Honda coolant can result in
corrosion, causing the cooling system to malfunction
or fail.
• To avoid burning out the element, do not operate the
engine block heater until it is installed in the vehicle and
you have added coolant.

DRAIN PLUG
FRONT

5.

With the vehicle on a lift, remove the engine splash
guard (one screw and three clips).

Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1.

Make sure you have the anti-theft code for the audio
unit and navigation system (if equipped), then write
down the radio station presets.

2.

Disconnect the negative cable from the battery.

3.

Allow the engine and all cooling system components
to cool down.
SCREW
3 CLIPS

2 of 6

AII 45089 (1011)

ENGINE SPLASH
GUARD

© 2010 American Honda Motor Co., Inc. – All Rights Reserved.

6.

Using a 19 mm socket, remove the drain bolt and
washer from the engine block. Coolant remaining in
the engine jackets will flow out the hole when the
plug is removed. Retain the plug; it will be used if the
engine block heater is removed.

8.

Measure and mark the heater harness at the point
shown. Install a wire tie with clip to the heater
harness at each of the measurements shown.
215 mm

NOTE: Use a new washer if the drain bolt is
reinstalled.

145 mm
HEATER
HARNESS

395 mm

WHITE
MARKER

MARK
A
B

C
WASHER

D
450 mm
615 mm

DRAIN
BOLT
(Retain.)
Use a 19
mm socket.

7.

9.

Install the engine block heater with aluminum
washer into the engine block using a 24 mm socket
with a 100 mm (4 in.) extension. Torque the engine
block heater to 60 N·m (44 lbf-ft). Using an extension
longer than 100 mm (4 in.) will give you an incorrect
torque reading.

Plug the heater harness connector into the engine
block heater. Temporarily place the entire heater
harness on top of the engine.
HEATER HARNESS
Put on the engine.

ENGINE
BLOCK
HEATER

ENGINE BLOCK HEATER
60 N·m (44 lbf-ft)
Use a 24 mm socket.

CONNECTOR

10. Lower the vehicle.

ALUMINUM
WASHER

© 2010 American Honda Motor Co., Inc. – All Rights Reserved.

AII 45089 (1011)

3 of 6

11. Remove the grille cover (eight clips).

CLIP
(Long)

13. Route the heater harness as shown, and secure
the two wire ties with clips (points A and B) to the
bracket.

6 CLIPS
(Short)

GRILLE COVER
CLIP
(Long)

FRONT

WIRE TIE
WITH CLIP
(point B)

WIRE TIE
WITH CLIP
(point A)

HEATER
HARNESS

12. Using one washer-bolt, install the bracket as shown.

BRACKET

14. Route the heater harness as shown. Using two black
wire ties, secure the heater harness to the vehicle
harness.
FRONT
BLACK
WIRE TIE

VEHICLE
CLIP
VEHICLE
HARNESS

VEHICLE
CLIP

WASHERBOLT

BRACKET

MARK

BLACK
WIRE TIE

MARK

VEHICLE
HARNESS
HEATER
HARNESS

VEHICLE
CLIP

Top View

BLACK
WIRE TIE

4 of 6

AII 45089 (1011)

© 2010 American Honda Motor Co., Inc. – All Rights Reserved.

15. Route the heater harness as shown and secure the
two wire ties with clips (points C and D) to the vehicle
frame.

17. Route the heater harness:
• Sport model: Route the heater harness as shown.
Using one black wire tie, secure the heater harness to
the front bumper grille. Attach the protective cap to
the front bumper grille, and plug the connector on the
heater harness into the protective cap.
FRONT
BUMPER

WIRE TIE
WITH CLIP
(point C)

BLACK
WIRE TIE

FRONT BUMPER
GRILLE

VEHICLE
FRAME
HEATER
HARNESS

WIRE TIE
WITH CLIP
(point D)

HEATER
HARNESS

16. Bundle the excess of the heater harness. Using
three black wire ties, secure the harness to the
vehicle harness.

HEATER HARNESS
CONNECTOR
PROTECTIVE
CAP

• Base model: Route the heater harness as shown.
Using one black wire tie, secure the heater harness to
the front bumper grille. Attach the protective cap to the
front bumper grille, and plug the connector on the
heater harness into the protective cap.

FRONT
BUMPER

FRONT BUMPER
GRILLE
BLACK
WIRE TIE

VEHICLE
HARNESS
HEATER
HARNESS
Bundle.
3 BLACK
WIRE
TIES

HEATER
HARNESS
HEATER HARNESS
CONNECTOR
PROTECTIVE
CAP

© 2010 American Honda Motor Co., Inc. – All Rights Reserved.

AII 45089 (1011)

5 of 6

18. Reinstall all removed parts.
19. Reinstall the radiator drain plug.
20. Fill the system with coolant. Follow the instructions
described in the service manual to fill and bleed the
cooling system.
21. Check the coolant reservoir for the correct level and
check the cooling system for signs of leakage.
Repair as necessary.
22. Check that the heater harness is routed properly and
all connectors are plugged in.
23. Put the drain plug (removed in step 6) in the glove
box.
24. Reconnect the negative cable to the battery.
25. Enter the audio unit anti-theft code, and reset the
radio station presets.
26. Reset the clock.

6 of 6

AII 45089 (1011)

© 2010 American Honda Motor Co., Inc. – All Rights Reserved.


Documents similaires


Fichier PDF 2011 fit engine block heater
Fichier PDF vmyma32
Fichier PDF 01 e85 complete vehicle
Fichier PDF ssp 87 1
Fichier PDF what is a camper
Fichier PDF 5u4ms67


Sur le même sujet..