HO OO Code 100 3 Way Turnout SL E99 .pdf


Nom original: HO-OO Code 100 3-Way Turnout SL-E99.pdf
Titre: SL-E99 Instr.indd
Auteur: brian

Ce document au format PDF 1.4 a été généré par Adobe InDesign CS4 (6.0) / Acrobat Distiller 9.0.0 (Macintosh), et a été envoyé sur fichier-pdf.fr le 07/03/2016 à 17:58, depuis l'adresse IP 78.251.x.x. La présente page de téléchargement du fichier a été vue 451 fois.
Taille du document: 78 Ko (1 page).
Confidentialité: fichier public




Télécharger le fichier (PDF)










Aperçu du document


UNIVERSAL
SUPER
ELECTROFROG

3-Way Electrofrog
Turnout (SL-E99)
Instructions

HO
OO

Contents:
1 Three Way Turnout, 1 Length of plastic sleeving,
2 Instruction leaflets

IMPORTANT Read these instructions and the main leaflet fully before proceeding
This turnout is supplied with two wires attached and is ready for connection to two single pole double
throw (SPDT) changeover switches – not supplied
The recommended way to operate the turnout is to complete the electrical circuitry using two Peco
Accessory Switches PL-13 in conjunction with two Peco Turnout Motors PL-10
1. The plastic sleeving supplied should be cut in
half and then slid over the two wires protruding from
underneath the turnout. Handle the wires carefully and
do not bend unnecessarily.The wires and sleeving are
intentionally long to allow for different wiring routes and
can be shortened once this has been decided upon.
2a. If Peco Ballast Inlay SL-69 is used the two wires
can be pushed through the ballast and then bent to lie
between the ballast and the baseboard. Remember at
this stage to cut two holes in the ballast to clear the two
turnout motors when they are fitted.
2b. If the turnout is laid with loose ballast, the wires
can be taken to the outside and along the edge of the
sleepers (to be hidden later by the ballast) or through
holes drilled in the baseboard.
3. Cut a hole in the baseboard 40mm x 54mm
(19⁄16” x 21⁄8”) to accept the assembled turnout motors/
switches. See diagram.

4. Attach the motors and switches to the turnout and
complete the wiring as shown in the diagram below.
Whenever possible this should be done before laying the
turnout so that the whole assembly can be tested first
as a unit.
5. If the three tracks leading from the turnout are
sidings and are not connected, no further electrical
breaks or wiring are necessary. However, should the
tracks be joined in any way, Peco Insulating Rail Joiners
SL-11 will be required on all rails at the frog end of
the turnout.

Manual Control
Should manual operation be preferred, it is still
necessary to wire the turnout in accordance with the
diagram using two single pole double throw switches.
The switches should be connected mechanically to the
tie-bars so that they operate together. As an example
the Peco Accessory Switches PL-13 can be fixed to the
baseboard alongside the turnout and connected to the
tie-bars with stiff wires or rods.
Hole in baseboard 40mm x 54mm

Wire with sleeving (see note 1)

Peco Accessory Switches PL-13

Track Power
Feeds

© PRITCHARD PATENT PRODUCT CO LTD, BEER, DEVON EX12 3NA, ENGLAND

01480

Wiring Diagram – viewed from underneath

03.10

Wire with sleeving (see note 1)


Aperçu du document HO-OO Code 100 3-Way Turnout SL-E99.pdf - page 1/1

Documents similaires


ho oo code 100 3 way turnout sl e99
ho oo code 75 3 way sl e199
sl e399 artwork a4
pl 10 series instructions
uhlenbrock 63410
peugeot 206 wiring diagram


Sur le même sujet..