ax52 .pdf



Nom original: ax52.pdf

Ce document au format PDF 1.4 a été généré par HP PDF Formatter version 1.0.0.229 / Adobe PDF Library 5.0, et a été envoyé sur fichier-pdf.fr le 04/10/2016 à 20:57, depuis l'adresse IP 90.116.x.x. La présente page de téléchargement du fichier a été vue 244 fois.
Taille du document: 1.6 Mo (8 pages).
Confidentialité: fichier public


Aperçu du document


I
<:

'--""-~~---'

-===

~ --==.~

uni en@
M

AX52
HAND- HELD TRANSCEIVER
OWNERS MANUAL

r

,...

.,

..

-

'."'

,

...' .. "

""

'==-='~l---'-'--'--"-----

-.

~~~-~

---

-.

DESCRIPTION
Your UNIDEN AX 52 represents the most advanced 2-watt hand-held type radio ever
designed for use in the Citizens Band Radio Service. It will operate on any three of the
40 frequencies designated as citizens band channels by the Department of Communications. Your Model AX 52 is factory-installed with channel 14 crystals. Additional crystals may be installed in the open channels.

WARNING
Before transmitting with your transceiver, you must obtain a Department of
Communications (D.O.C.) Citizens Radio Licence. Obtain an application
form, from the D.O.C. Before completing the form you should read the
conditions governing the licensing and operation of the C.R.S. (D.O.C.
brochure RB ~49). This brochure also can be obtained from the D.O.C. After
completing the application form, mail it with the appropriate fee to the
Superintendant Regulatory of Licensing in the State or territory in which the
station will be operated.

SPECI FICA TIONS:
TRANSMITTER
: 2 Watts
: 1 Watt
: -65 dB or better
: 480 mA to 550 mA

Power Input
Power Output
Spurious Ratio
Current Drain at Maximum Modulation
RECEIVER
Sensitivity at 10 dB S-N/N
Image Rejection Ratio
IF Rejection Ratio
Audio Output Power at 10% Distortion
Current Drain at Maximum Output Power (DC)

:
:
:
:
:

0.5jJ.V
15 dB
80dB
0.5 Watts
400 mA to 450 mA

-1.1:
~I

CHANNEL

INFORMATION

Channel

Channel Frequency
inMHz

Channel

Channel Frequency
in MHz

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

26.965
26.975
26.985
27.005
27.015
27.025
27.035
27.055
27.065
27.075
27.085
27.105
27.115
27.125
27.135
27.155
27.165
27.175
27.185
27.205

21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

27.215
27.225
27.255
27.235
27.245
27.265
27.275
27.285
27.295
27.305
27.315
27.325
27.335
27.345
27.355
27.365
27.375
27.385
27.395
27.405

...

-

PREPARING FOR USE
1. Slide off the Battery Compartment cover to install the batteries.
2. You can use the following types of batteries (size "AA").
Description
Rechargeable Nickel Cadmium
Alkaline type
Standard type

Quantity Required
(1.2 volts)
(1.5 volts)
(1.5 volts)

10
8
8

Alkaline or rechargeable batteries are more desirable.
3. Install the batteries with polarity as shown on the Battery Compartment.
4. If you are using Alkaline or Standard type "AA" batteries, use the two dummy
batteries provided with this unit.
NOTE: Only Nickel Cadmium batteries can be used for recharging purposes.
5. If the battery indicator LED comes on when power is turned on, the batteries need
to be recharged or replaced. As long as the LED stays "off", the batteries are OK.

-2-

--

:::=0

T

~
1

._~

CONTROLS AND FUNCTIONS

ANTENNA
Extend to its full length

PUSH-TO-TALK
Press to talk.
Release to listen

BUTTON

BATTERY LOW INDICATOR LED
If LED comes on, recharge or
replace batteries.
CHANNEL SELECTOR
Position 1 is for
Channel 14 (crystals
supplied with the unit).
Use 2 and 3 for other
channels as desired.

SQUELCH
Adjust to eliminate background
noise.

EXTERNAL ANTENNA JACK
Connect an external antenna for
greater operating range.

EXTERNAL SPEAKER JACK
Connect an optional external
speaker.

CHARGER JACK
Connect charger to recharge
Nickel Cadmium batteries
without removing them.

POWER ON-OFFNOLUME CONTROL
Turn clockwise past click to apply power.
Adjust for desired listening level.

MICROPHONE

Talk here.

POWE R JACK
Connect an optional to AC
Adaptor to operate the unit on
household current.

-3-

~
J

l
OPERATING

PROCEDURE TO TRANSMIT

1. Extend Antenna to its full length and keep in a vertical position.
IMPORTANT: IF THE ANTENNA IS NOT FULLY EXTENDED, THE EFFICIENCY OF THE TRANSMITTER IS REDUCED AND THE
POWERAMPLIFIERTRANSISTORCOULD BE DAMAGED.
2. Turn the power "on" by rotating the Volume Control clockwise.
3. Set the Channel Selector to the desired channel.
4. To transmit, press the Talk button. Speak slowly and clearly in normal voice, "2"
to "3" from the Microphone.
5. To receive, release the Talk button.

OPERATING

PROCEDURE TO RECEIVE

1. Extend Antenna to its full length and keep in a vertical position.
2. Turn the unit "on" by rotating Volume Control clockwise.
3. Set the Channel Selector to the desired channel.
4. Set the Volume Contr91 to a comfortable listening level.
5. Listen to the background noise from the speaker. Turn the Squelch Control slowly
clockwise until the noise JUST disappears (no signal should be present). Leave the
control at this setting. The Squelch is now properly adjusted. The receiver will
remain quiet until a signal is actually received. Do not advance the control too far,
or some of the weaker signals will not be heard.

RANGE
The range of your hand-held transceiver will vary depending on conditions. Factors
such as antenna, terrain and battery charge all affect range. To insure maximum range,
always keep fully charged batteries in the unit. As voltage decreases, it directly affects
range. Though higher in initial cost than other types, Nickel Cadmium Rechargeable
Batteries are recommended. They can be recharged hundreds of times.

CHANGING

OR INSTAlliNG

NEW CRYSTALS

Your AX- 52 comes with Channel 14 installed in Channel 1 position. You can use any
3 channels of the 40 alloted to CB Band. Do not attempt to use non-standard crystals
or to make any internal adjustments to your AX-52. Such is prohibited by the D.O.C.
and result in illegal operation, for which you may be liable and may be fined. Therefore, replacing and/or installing crystals must be made by or under supervision of the
holder of an D.O.C. issued 1st or 2nd class radio operator license. Following information is provided only for such license holders.
1. Remove the rear cover from the transceiver.
2. Insert transmit crystal into the dual pin socket marked TX-2 or TX-3 (see below).
3. Insert receive crystal into the dual pin socket marked RX-2 or RX-3.
-4-

.:[

I

NOTE: The crystals installed in channel 1/1"position are also of plug-intype and may
be replaced with those of any other channels.
Make sure the transmit and receive crystals are installed in their correct
sockets. If the crystals are reversed, the unit will transmit on one frequency
and receive or another, both of which will be outside the citizens band,
resulting in illegal operation.
4. Replace the rear cover.

CRYSTALSOCKET LOCATION
TX:

Transmit crystal
R2~

G-

RX: Receive crystal

R26

~

R20 CI7 ..

~+

--€) <=>i:i

~

R23
<381-.

~~~ ~~
CII

".~o

o~

~

+~R24

(TX)

C78

-c::::::J:7...

~

- ~
R 14
U
-.;I
-€>
&J
--€>

C20

r:

0:~

~+

G8-~

2

~ TRI6

TR7

L4

C5

0:

c::;r==-

O
DID

TRa~9:
~ = R6
ca <==> c:::>
R9

..

~-1'\

C31

0

.. C72...:ch
TRI5 ~~~ G:!.~
u D9
... R66 ... ~

gj

:;;11 ~~., a '" ~C32
~~T~
JP I
JP 2

CID

""'"L-5-~

RISZ
<==>C38.- R1S3~
~36
~RIS4=c::::J-

RC;;"'

-JPI2

CI5

i:i'"

c:::> VR3
INRn{>
TR6=a-6'" \..:!!!!

1

d>!! RI!

i ~0

y
..

'~f
D~
r3

~

O

..R33
...

~

'"
...

34 U
N
--€)C4
...
R7
R27
(7!!.L
<7:
~
G-R4
f19G-R3 TBI"""
I

l

C3<==>

R2
C2 --€)

:J O

1,

<==>

---1!!:A

2
C5O

3

:;

IlUV~
02
2 RX-<f 03R~

...

-+=€>

3J

o~

TPZ R41S S 2

J;5

C

~~"'9C45C=~
JP6 on . ~ I
...

SERVICING YOUR TRANSCEIVER
The technical information, diagrams and charts will be supplied upon request.
It is the user's responsibility to see that this radio is operating at all times in accordance with the D.O.C. Citizens Radio Service regulations.
We highly recommend that you consult a qualified radiotelephone technician for the
servicing and alignment of this CB radio product.
Please refer to the WARNING information contained in the 1st page of your Owner's
Guide.
(NOTE: When ordering parts, it is essential to specify the correct model number and
serial number of the unit.)
-5-

.-...

'

,f

~

.---....

MEMO

-6c:'

.:r
1,

'

~1i~1i

unlden@
TWO-YEAR

FULL WARRANTY

WARRANTOR. SANTRONIC AGENCIES PTY. LTD. 13 Garema Circuit,
Kingsgrove MSW 2208 ("SANTRONIC").
ELEMENTS OF WARRANTY. SANTRONIC warrants, for the duration of this
warranty, its UNIDEN CB Product to be free from defects in materials and craftsmanship with only the limitation or exclusions set out below.
WARRANTY DURATION. This Warranty shall terminate and be of no further effect
Two (2) years after the date of original purchase of the Product or at the time the
Product is (a) damaged or not maintained as reasonable and necessary, (b) modified,
(c) improperly installed, (d) is repaired by someone other Warrantor for a defect or
malfunction covered by this Warranty, or (e) used in a manner or purpose for which
the Product was not intended.
PARTS COVERED. This Warranty covers all components of the Products.
STATEMENT OF REMEDY. In the event that the Product does not conform to this
Warranty at any time while this Warranty is effective, Warrantor will repair the defect
and return it to you prepaid, without charge for parts, service, or any other costs
incurred by Warrantor or its representatives in connection with the performance of
this Warranty. In addition, if the Product contains a defect or malfunction which is
not repaired after a reasonable number of attempts by Warrantor to repair the
Product, the Product or defective component will at our discretion, will be replace
without charge, when the defective product is delivered to the warrantor at 13
Garema Circuit Kingsgrove NSW 2208 free and clear of all liens and encumbrances.
Please note that while the Product will be remedied under this Warranty without
charge. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Some states do not allow this exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY. In the event
that the Product does not conform to this Warranty, the Product should be shipped
prepaid to Warrantor at 13 Garema Circuits Kingsgrove NSW 2208. THE ORIGINAL
OR COpy OF THE SALES RECEIPT OR OTHER VALID EVIDENCE OF THE
DATE OF THE ORIGINAL PURCHASE MUST ACCOMPANY THIS PRODUCT.
LEGAL REMEDIES. This Warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

Sanlronlc )
AGENCIES PTY. LTO.
13 GAREMA CIRCUIT. KINGSGROVE
PHONE 7581522, TELEX AA73170
P.O. Box 12, Kingsgrove, NSW 2208
BRISBANE: 3/12 RANDALL ST
SLACKS CREEK, OLD 4127
PHONE 07 290 1188

UTSN01267

EZ

@Copyright 1984Uniden Corporation

Printed

in Taiwan

'

==:f

j


ax52.pdf - page 1/8
 
ax52.pdf - page 2/8
ax52.pdf - page 3/8
ax52.pdf - page 4/8
ax52.pdf - page 5/8
ax52.pdf - page 6/8
 




Télécharger le fichier (PDF)


ax52.pdf (PDF, 1.6 Mo)

Télécharger
Formats alternatifs: ZIP



Documents similaires


ax52
pro530xl 1
ax55
pro340xl 1
raptor om
cb major m360 user

Sur le même sujet..