mk7 traction int .pdf



Nom original: mk7-traction-int.pdf

Ce document au format PDF 1.5 a été généré par Adobe InDesign CS5 (7.0) / Adobe PDF Library 9.9, et a été envoyé sur fichier-pdf.fr le 16/03/2018 à 23:28, depuis l'adresse IP 82.242.x.x. La présente page de téléchargement du fichier a été vue 375 fois.
Taille du document: 1.1 Mo (11 pages).
Confidentialité: fichier public


Aperçu du document


MK7 GOLF TRACTION CONTROL BUTTON KIT
P art # U S P 1 1 9 6

7716 Wiles Rd.Coral Springs, FL 33067
www.uspmotorsports.com

MK7 GOLF TRACTION
CONTROL BUTTON KIT

Install instructions

USP1196 II

7716 Wiles Rd.Coral Springs, FL 33067
www.uspmotorsports.com

2

Install instructions

1. Pull up on shift boot as indicated until out of the way.

USP1196 II

MK7 GOLF TRACTION
CONTROL BUTTON KIT

2. Pull up on lower horse shoe shaped plastic and remove.

3

Install instructions

3. Remove OEM buttons by pushing forward on clip at “1” then
pull up at “2”.

USP1196 II

MK7 GOLF TRACTION
CONTROL BUTTON KIT

4. This will allow the entire 3 button piece to come up and out.

4

Install instructions

5. Remove hood disengagement lever by pulling as shown.

USP1196 II

MK7 GOLF TRACTION
CONTROL BUTTON KIT

6. Loosen lower kick panel by pulling up at the front, allowing to
slide front portion to the side in order to access front kick panel.

5

Install instructions

7. Remove front side kick panel which previously held hood release lever. Begin pulling up at base which was covered by lower
kick panel, working up the door frame.

USP1196 II

MK7 GOLF TRACTION
CONTROL BUTTON KIT

8. Remove headlight switch by pressing center knob in and turning clockwise to first selector. This will disengage securing tabs
and now allow removal of the switch by pulling directly out.

6

Install instructions

MK7 GOLF TRACTION
CONTROL BUTTON KIT

9. Unplug OEM harness from headlight switch and connect into
supplied female jumper harness.
10. Connect male end of jumper harness into headlight switch.
Then feed jumper harness into dash and down towards footwell.

USP1196 II

7

Install instructions

11. Having removed the front side kick panel, there are 4 connectors that are now visible. Locate the black connector at the
top left and unplug.

USP1196 II

MK7 GOLF TRACTION
CONTROL BUTTON KIT

12. Turning the connector upside down (connector securing tab is
now facing down), insert supplied wire pin into slot 5 as shown.

8

MK7 GOLF TRACTION
CONTROL BUTTON KIT

Install instructions

13. Plug connector back in and route new wire around harness,
securing with zip ties.

USP1196 II

9

Install instructions

MK7 GOLF TRACTION
CONTROL BUTTON KIT

14. Route and secure remaining harness behind paneling and out
shifter hole.
15. Run harness into slotted area and connect to new traction
control switch.

USP1196 II

10

Install instructions

MK7 GOLF TRACTION
CONTROL BUTTON KIT

17. Replace all panels in reverse order and enjoy easily disabling
your traction control.
16. Slide new traction control buttons into place and push down
until secure.

USP1196 II

11




Télécharger le fichier (PDF)

mk7-traction-int.pdf (PDF, 1.1 Mo)

Télécharger
Formats alternatifs: ZIP







Documents similaires


mk7 traction int
magnum 1012 om
vmyma32
r12rt bike plastic removal part 1
http www hmaservice com v
instruction speedstar2

Sur le même sujet..