Recherche PDF

−i, −−id=ID Display data for a single specified GPU or Unit.

Batteries approved from 2011 onwards must comply with the weight range specified under manufacturers data.

REQUEST PARAMETERS Name Type Description apiKey string The API key provided for your user. If it is not specified, the request will return the error code "30 ­ Missing (required) signature mandatory parameter". If the key is incorrect the request returns the error code "41 ­ Invalid credentials".

Batteries approved from 2011 onwards must comply with the weight range specified under manufacturers data.

• Use coolant of specified mixing rate.

• Use coolant of specified mixing rate.

The clearance must be within the specified limits (Sect.

Comparison 10 Any method with a specified protocol of simultaneous versus sequential pumping, Outcome 1 Quantity of milk expressed.

All players in civilian clothes without weapons in hand are considered civilians All players with civilian costumes with fire weapons in hand are considered cartel unless specified differently.

Use any size needles to obtain specified gauge.

Color values have been specified for each of the colors in the ManpowerGroup palette and the approved transparencies (at right).

SERVICE Observance of the service, maintenance and tuning instructions for the engine and chassis specified in the Owner's Manual is a prerequisite for faultless operation and the avoidance of premature wear.

Request for/confirmation of bearing and distance to specified point.

Modem has connected to the remote address as specified.

The two (2) ATS Units concerned shall keep each other advised of any changes in the operational status of the facilities and navigational aids which may affect the procedures specified in this Letter of Agreement.

Different programming times are necessary depending on the production age of the vehicle and the work already performed on the vehicle so that no time requirements can be specified here.

3 Standard 2.92 – 3.08 (0.115 – 0.121) 3.72 – 3.88 (0.146 – 0.153) 13.85 – 13.96 (0.542 – 0.550) 13.90 – 14.00 (0.547 – 0.551) — 37.13 (1.462) 14.000 – 14.043 (0.5512 – 0.5529) 13.957 – 13.984 (0.5495 – 0.5506) 33.600 – 33.662 (1.3228 – 1.3253) 33.550 – 33.575 (1.3209 – 1.3218) Brake fluid DOT 4 Limit 2.62 (0.103) 3.42 (0.135) 13.05 (0.514) 13.10 (0.516) 0.10 (0.004) 35.3 (1.39) — — — — — Tightening Torque Specifications B823H15307002 N˜m Tightening torque kgf-m lb-ft 6 0.6 4.5 Clutch master cylinder holder bolt Clutch hose union bolt 10 1.0 7.0 23 2.3 16.5 Clutch lever pivot bolt Clutch lever pivot bolt lock-nut Clutch release mounting bolt Clutch spring support bolt Clutch sleeve hub nut Clutch spring set bolt Clutch cover bolt 1.0 6.0 10 23 150 10 10 0.1 0.6 1.0 2.3 15.0 1.0 1.0 0.7 4.5 7.0 16.5 108.5 7.0 7.0 Fastening part Air bleeder valve (Clutch) Note )(Page 5C-5) / )(Page 5C-6) )(Page 5C-8) )(Page 5C-9) / )(Page 5C-12) )(Page 5C-10) )(Page 5C-10) )(Page 5C-12) )(Page 5C-18) )(Page 5C-19) )(Page 5C-20) )(Page 5C-21) NOTE The specified tightening torque is also described in the following.

TOLERANCE IF NOT OTHERWISE SPECIFIED 15 2 16 "

TOLERANCE IF NOT OTHERWISE SPECIFIED 15 2 16 "

All prices are only valid regarding the specified colours and products.

The values specified in this table apply to all screw connections conforming to the aforementioned conditions.

• Be sure to tighten fasteners including bolts and nuts to the specified torque.

Data beside it indicates specified torque.

If this information is important, it can be specified in some other way, or the productions can be written in the usual recursive fashion.

IGNITION SYSTEM MX’er 50 SERVICE INFORMATION GENERAL INSTRUCTIONS • Check the ignition system according to the sequence specified in the Troubleshooting.