Dépose pare choc avant w166

AR88.20-P-2000GQ

MODEL

1
2
3
4a
4b
4c

Remove/install front bumper

24.7.12

166

Cover
Expansion rivet
Connector
Screw
Screw
Screw

P88.20-3866-06

Shows model 166.874
5

Screw

P88.20-3897-04

Remove/install
General information on the impact absorber
1

Disconnect battery ground cable

2
3
4
5

Open engine hood
Remove cover (1)
Remove expansion rivet (2)
Detach left and right front section on fender
liner in front fenders in area of bumper
Remove corresponding underfloor paneling
Disconnect electrical connectors (3)

6
7
8
9
10
11
12
13
14

Unscrew bolts (5) on right and left fender
flare
Unscrew left and right bolt (4a)
Loosen left and right bolt (4b)
Loosen left and right bolt (4c)
Unhook bumper at sides and remove toward
front
Install in the reverse order
Adjust bumper

AH88.20-P-1000-01A
MODEL 166
with CODE U60(Pedestrian protection)

AR88.40-P-1000GQ

AR88.10-P-1300GQ
AR61.30-P-1001GQ
The number of electrical connectors (3)
differs depending on the vehicle equipment.
MODEL 166.874

MODEL 166.8

Gap dimension
Gap dimension
© Daimler AG, 3/15/19, G/03/14, ar88.20-p-2000gq, Remove/install front bumper
MODEL 166

AR54.10-P-0003GZ

AR60.00-P-0700-01GQ
*BE60.00-P-1002-01Z
*BE60.00-P-1001-01Z
Page 1 of 2

15

Check PARKTRONIC operating state

Feeler gauge
MODEL 166
with CODE 220(PARKTRONIC)
with CODE 235(Active Parking Assist)

*129589032100

Switch on ignition and PARKTRONIC,
engage reverse gear and release parking
brake. PARKTRONIC automatically performs a
self-test and operational readiness is
signaled via the warning indicator.
16

Calibrate camera with STAR DIAGNOSIS
MODEL 166
with CODE 501(360 degree camera)

AD00.00-P-2000-04A

Test and adjustment values for gap dimensions

Number
BE60.00-P-1001-01Z

Designation
Gap dimension

Engine hood to
fender
Engine hood to
headlamp
Engine hood to
bumper
Fender to A-pillar
Front door to fender
Front door to rear
door
Rear door to rear
fender

Dimension "A"

mm

MODEL 166
3,8 ( 1)

Dimension "B"

mm

3,9 ( 1)

Dimension "C"

mm

5,4 ( 1,5)

Dimension "D"
Dimension "E"
Dimension "F"

mm
mm
mm

3,5 ( 1)
4,3 ( 0,7)
4,8 ( 0,7)

Dimension "I"

mm

4,3 ( 0,7)

AR60.00-P-0700-01
For
picture, G
see

Test and adjustment values for gap dimensions

Number
BE60.00-P-1002-01Z

Designation
Gap dimension

Bumper to headlamp Dimension "S"
Fender to headlamp Dimension "R"
Engine hood to ADimension "Q"
pillar

mm
mm
mm

MODEL 166
3 ( 0,5)
3,9 ( 1)
3,5 ( 1)

For
AR60.00-P-0700-01
picture, GQ
see

129 589 03 21 00
Feeler gauge

© Daimler AG, 3/15/19, G/03/14, ar88.20-p-2000gq, Remove/install front bumper
MODEL 166

Page 2 of 2